Take your 1964–1966 Mustang’s rear suspension to the next level with QA1’s fully engineered 4-link and 9-inch housing system. This complete kit replaces outdated leaf springs with a modern triangulated 4-link and double adjustable coilovers - giving you full control over ride quality, stance, and handling. Designed for street performance, autocross, or restomod builds, it’s a serious performance upgrade that fits like it belongs there.
BUILT FOR PERFORMANCE & PRECISION
QA1’s 4-link design eliminates axle wrap, wheel hop, and the inconsistencies that plague leaf-spring setups. Geometry-optimized brackets maintain correct pinion angle and suspension alignment through the full range of motion, providing improved traction and predictable handling on any road surface.
DOUBLE ADJUSTABLE COILOVERS
Fine-tune your Mustang’s performance with QA1’s double adjustable shocks, which independently control rebound and compression. Whether you’re dialing in for track conditions or adjusting for a smoother street ride, you get precise control with 18 clicks of adjustment on each circuit.
STRENGTH MEETS STYLE
Each kit includes QA1’s custom fabricated 9-inch housing, engineered for serious horsepower and clean fitment. The housing’s formed brackets, heavy-duty 3” OD ¼” wall axle tubes, and 31-spline alloy axles deliver maximum rigidity and support up to 800 HP. Combined with a semi-gloss powder coat finish, it’s as tough as it looks.
RIDE HEIGHT FLEXIBILITY
Easily adjust ride height from factory stock height to 3” lower, giving you full control over stance without compromising drivability or geometry.
Features:
- Application-specific fit for 1964–1966 Ford Mustangs
- Complete rear suspension system: 9” housing, 4-link, and coilovers
- Double adjustable shocks: independent rebound and compression control
- Adjustable ride height from stock to –3”
- Eliminates wheel hop and axle wrap
- Heavy-duty fabricated 9” housing rated to 800 HP
- 31-spline 1541H alloy axles rated to 650 HP
- Big Ford “New Style Torino” flanges with 2.5” axle offset
- 5x4.5” bolt pattern for wide wheel compatibility
- Includes drain plug, fill plug, vent port, and jack pad for easy service
- ½” x 3” wheel studs for better fitment with aftermarket wheels
- Durable semi-gloss powder coat finish
- Weld-in installation with self-fixturing brackets for perfect alignment
- Made in the USA
Notes:
- Fits 1964–1966 Ford Mustangs
- For use with QA1’s included 9” rear housing
- Requires 31-spline Ford 9” third member (sold separately)
- Factory wheel mounting surface: 57-3/8”
- Big Ford “New Style Torino” flanges (2.5” offset)
- 5x4.5” bolt pattern (standard Ford)
- Weld-in installation required
WARRANTY / DISCLAIMER
QA1 warrants that the products will be free from defects in material and workmanship for one year from date of sale to the original purchaser. A limited lifetime warranty is offered on select shock absorbers. For registration and more information on the limited lifetime warranty, please visit https://www.qa1.net/Warranty. QA1 makes no other warranty of any kind, express or implied. QA1 shall have no obligation under the foregoing warranty where the defect is the result of improper or abnormal use, your negligence, vehicle accident, improper or incorrect installation or maintenance, nor when the product has been repaired or altered in any way. QA1's liability in the case of defective products subject to the foregoing warranty shall be limited to the repair or replacement, at QA1's option, of the defective products. Consequential or incidental damages are not recoverable under this warranty. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.
- QA1, in its sole discretion, shall determine whether or not any Eligible Product is defective or otherwise covered by this warranty.
- If the Eligible Product fails to perform properly due to defective materials or workmanship, QA1 will at its option either (i) repair the Eligible Product without charge, or (ii) replace the Eligible Product. If the Eligible Product is no longer available, QA1 will replace the Eligible Product with an equivalent product. No refunds will be provided.
- The warranty provided by QA1 does NOT apply if the Eligible Product fails to perform:
- due to cosmetic wear and tear from normal use;
- due to improper or abnormal use, abuse, neglect, negligence, vehicle accident, insufficient travel, improper or incorrect installation or maintenance; or
- when the Eligible Product has been repaired, replaced, substituted or altered in any way, or if used with parts other than genuine parts of QA1.
- QA1 is not responsible for installation or removal labor, or for any other repair charges associated with the Eligible Product.
- Customer pays shipping to QA1 for final determination on eligibility. Any repaired or replaced Eligible Product will be returned to customer excluding freight cost.
- QA1 shall not be liable for the loss of use of the Eligible Product, loss of time, inconvenience, commercial loss or any other indirect, consequential, special or incidental damages due to breach of the above limited lifetime warranty. QA1 makes no warranties of any kind, express or implied, other than as herein expressly provided, and specifically disclaims the implied warranties of merchantability and fitness for a particular purpose. Notwithstanding anything set forth herein to the contrary, QA1’s liability hereunder shall be limited to the purchase price of the Eligible Product.
In order to be eligible for service under this warranty, you must return the defective part to QA1 together with a RMA. number issued from QA1. Tag each item with the part number and the specific explanation of defect. We will inspect the part and determine: a) if it is eligible for repair or replacement; and, b) if so, whether to repair or replace it. All returns must be shipped prepaid to: QA1 Precision Products, Inc., RMA#__________, 9574 217th Street West, Lakeville, MN 55044.
THE BUYER UNDERSTANDS AND EXPRESSLY RECOGNIZES that racing parts, specialized street rod equipment, rod end bearings, and ALL parts and services sold by QA1 are exposed to many and varied conditions due to the manner in which they are installed and used. BUYER ACKNOWLEDGES that QA1 does not have full knowledge of the intended use of the goods, and BUYER WILL DEFEND AND INDEMIFY QA1 upon demand against all claims, actions, liability, loss and expense (including investigating expense and attorney fees incurred in litigation or because of threatened litigation) for any loss, damage or injury, either to a person or to property, resulting from the direct or indirect use of any QA1 products or inability by the buyer to determine proper use or application of QA1 products. With the exception of the limited liability warranty set forth above, QA1 SHALL NOT BE LIABLE FOR ANY CLAIMS, DEMANDS, INJURIES, DAMAGES, ACTIONS, OR CAUSES OF ACTION WHATSOEVER TO BUYER ARISING OUT OF OR CONNECTED WITH THE USE OF ANY QA1 PRODUCTS. MOTORSPORTS ARE DANGEROUS; AS SUCH, NO WARRANTY OR REPRESENTATION IS MADE AS TO THE PRODUCT'S ABILITY TO PROTECT THE USER FROM INJURY OR DEATH. THE USER ASSUMES THAT RISK.
