5" Performance Elite Lift Kit W/ 4-link 4WD Gas - BDS2214FPE

$6,025.55
SKU:
BDS2214FPE
Free Shipping Eligible
Minimum Purchase Required
SKU:
BDS2214FPE

5" Performance Elite Lift Kit W/ 4-link 4WD Gas - BDS2214FPE

Raise the height of your Ford Super Duty gas powered truck with this 5-inch lift kit and 4-Link conversion from BDS Suspension. Designed to improve stance performance and capability this kit includes everything necessary to set your truck up right with clearance for up to 37" tires. Up front the lift kit includes gasoline-specific Pro-Ride coil springs 4-link control arms with conversion brackets forged drop pitman arm and track bar bracket for steering correction sway bar relocation brake line brackets and precision tuned nitrogen charged shocks. In the rear this kit utilizes a high-strength fabricated lift block longer u-bolts brake line brackets and a matching set of NX2 Nitro or FOX Performance shocks. 4-Link Conversion Convert the factory stamped steel radius arms over to the BDS 4-link to optimize suspension geometry for better handling characteristics while adding strength and stability. This bolt-on upgrade utilizes high-strength ¼-inch steel brackets that allow mounting of HD upper and lower control arms to correct axle positioning while limiting caster change throughout wheel travel. Pro-Ride Coil Springs A pair of full-length gasoline-specific Pro-Ride coil springs are supplied to provide the correct lift height and smooth predictable ride across various terrains. Steering Correction To optimize steering geometry once lifted a forged drop pitman arm is used to minimize the steering angle and pair it with a heavy duty track bar drop bracket to keep them in phase through suspension travel while recentering the front axle.

Features-

  • Easy 100% Bolt-on installation
  • Pro-Ride dual rate coil springs provide a remarkable ride through any terrain
  • Heavy duty 4-Link control arms offer improved handling stability strength and caster control during wheel travel
  • Track bar relocation bracket and pitman arm maintain proper steering angles for improved handling
  • Fabricated steel blocks provide level stance from front to rear
  • Standard NX2 Nitro shocks with vehicle-specific valving for better control
  • Upgrade to FOX 2.0 Performance Series shocks for maximum performance on and off-road

Details-

  • Installation Time: 8-10 Hrs
  • Installation Difficulty: difficult
  • Installation Tools: cutOffTool-puller pitmanArm
  • Rear Lift Height: 5IN
  • Front Lift Method: Coil Spring
  • Rear Lift Method: Block
  • Front Lift Height: 5IN
  • Rear Lift Option: Leaf Springs
  • Shocks Included: Yes

Notes-

  • Ford recommends the replacement of the pitman arm nut after each time it has been removed.
  • If installed on a truck with a top-mounted overload spring an overload spacer block taller than 1-1/8" UBT4027 (Qty: 4) is required.
  • Front exhaust modification may be required to clear the front drive shaft (Gas Only).
  • Use a small pitman arm puller to remove the drag link joint and steering stabilizer taper.
  • If your truck is equipped with a 2-piece rear driveshaft a Carrier Bearing Drop Kit may be required: BDS123402.
  • Due to the taller factory ride height Tremor models will not net the full advertised lift height. The final ride height will be the same as standard models.
  • Larger tires on the stock wheel are not recommended due to the brake line clearance required. Use recommended specs listed in the wheel and tire fitment section.
  • Minor trimming may be necessary for clearance of 37x12.50 tires on certain wheel setups.
  • Installation requires a torque wrench capable of 405 ft-lbs.
  • Some trucks with a rear driveline vibration may have a recall from Ford regarding the rear axle. (Safety Recall 21S31) Due to the recall procedure BDS recommends having this performed prior to installing the lift.


BDS Suspension Part # BDS2214FPE

Wearable Parts - Limited Lifetime Warranty BDS NX2 Series Shocks and BDS/Fox Performance Series Shocks: Shock oil seals are not covered by this Limited Lifetime Warranty because they are subject to wear over time and use. At BDS's discretion, leaking shock seals less than 2 years from date of purchase, free from contamination, damage, or abnormal seal wear due to misuse can be considered for repair or replacement under warranty. A shock absorber is a wear item and over time will experience diminished damping resistance due to normal component wear. This is not a defect in material or workmanship and is therefore not warrantable. Defects in material and workmanship do not include such things as dented cylinders or bent rods caused by obvious side impact, rust or corrosion. Fox Proprietary Shocks and Coil Overs: Fox Proprietary parts are covered by their warranty and are not included in the BDS Warranty. BDS may offer to assist with the warranty of defective product, at our discretion. Other warranty concerns should be handled through the Fox Service program. Leaking shock seals less than 1 year from date of purchase, free from contamination, damage, or abnormal seal wear due to misuse can be considered for Warranty. FOX service information can be found here: https://www.ridefox.com/service.php?m=truck Ball Joints and Tie Rod Ends: These items are subject to normal wear over time. However, Ball Joints and Tie Rod ends less than 3 years from the date of purchase, that have been properly greased, maintained, and do not show signs of abnormal use can be considered for warranty. BDS Suspension's obligation under all warranties is limited to the repair or replacement, at BDS's option, of the defective material. BDS will cover the cost of ground shipping on warranty items, and a return shipping label if we require the warranty part to be returned to us. Any cost of removal, installation or reinstallation, expedited freight charges, incidental or consequential damages are expressly excluded from these warranties. Proof of purchase is required for all warranty claims.

Reviews & Questions