4" Lift Kit W/ Radius Arms Diesel W/O Overload and 8-bolt T-case - BDS1658FPE

$5,122.65
SKU:
BDS1658FPE
UPC:
840416406092
Free Shipping Eligible
Minimum Purchase Required
SKU:
BDS1658FPE
UPC:
840416406092

4" Lift Kit W/ Radius Arms Diesel W/O Overload and 8-bolt T-case - BDS1658FPE

Take your RAM 3500 diesel powered truck to the next level with this 4-inch radius arm lift kit from BDS Suspension. Designed to improve stance performance and capability this kit includes everything necessary to set your truck up right with clearance for up to 35" tires. Up front the lift kit includes diesel-specific Pro-Ride coil springs heavy-duty replacement radius arms forged drop pitman arm and track bar bracket for steering correction sway bar relocation brake line brackets and precision tuned NX2 or FOX 2.0 nitrogen charged shocks. At this height the transfer case needs to be indexed to allow use of the factory front driveshaft so an indexing ring and new transmission crossmember are supplied. In the rear this kit utilizes a high-strength fabricated lift block longer u-bolts and a matching set of NX2 Nitro or FOX 2.0 Performance shocks. HD Radius Arms In place of the factory stamped steel radius arms BDS supplies a pair of high-strength tubular radius arms. These arms mount into the factory location and offer caster adjustment for a wide range of lift heights along with an OE-style rubber bushing at the frame mount for smooth quiet service-free operation. Pro-Ride Coil Springs A pair of full-length diesel-specific progressive rate Pro-Ride coil springs are supplied to provide the correct lift height and smooth predictable ride across various terrains. Steering Correction To optimize steering geometry once lifted a forged drop pitman arm is used to minimize the steering angle and pair it with a heavy duty track bar drop bracket to keep them in phase through suspension travel while recentering the front axle.

Features-

  • Heavy duty tubular radius arms improve strength handling and caster control
  • Front high strength progressive rate coil springs for a great ride on any terrain
  • Front track bar relocation bracket to re-position axle
  • Forged drop pitman arm to correct steering angles
  • Front sway bar correction to maintain handling performance
  • HD transmission crossmember and t-case indexing ring to correct front driveline angles and allow use of factory driveshafts
  • BDS NX2 gas or FOX performance series IFP gas shocks to improved ride and offroad performance

Details-

  • Installation Time: 8-10 Hrs
  • Installation Difficulty: moderate
  • Installation Tools: puller pitmanArm
  • Rear Lift Height: 3IN
  • Front Lift Method: Coil Spring
  • Rear Lift Method: Block
  • Front Lift Height: 4IN
  • Rear Lift Option: Without Factory Rear Overload Leaf
  • Indexing Ring Option: 8 Bolt
  • Shocks Included: Yes

Notes-

  • Dually with 8-bolt Transmission (Aisin) require BDS122409Def Relocation Kit
  • Mega Cab’s with 8-bolt Transmission (Aisin) require BDS122409 Def RelocationKit
  • Vehicles equipped with a Manual T-case requiresBDS122423 Manual transfer case shifter extension
  • Vehicles equipped with a 2-piece rear drive shaft (carrier bearing) requireBDS122406 Carrier bearing drop.


BDS Suspension Part # BDS1658FPE

Wearable Parts - Limited Lifetime Warranty BDS NX2 Series Shocks and BDS/Fox Performance Series Shocks: Shock oil seals are not covered by this Limited Lifetime Warranty because they are subject to wear over time and use. At BDS's discretion, leaking shock seals less than 2 years from date of purchase, free from contamination, damage, or abnormal seal wear due to misuse can be considered for repair or replacement under warranty. A shock absorber is a wear item and over time will experience diminished damping resistance due to normal component wear. This is not a defect in material or workmanship and is therefore not warrantable. Defects in material and workmanship do not include such things as dented cylinders or bent rods caused by obvious side impact, rust or corrosion. Fox Proprietary Shocks and Coil Overs: Fox Proprietary parts are covered by their warranty and are not included in the BDS Warranty. BDS may offer to assist with the warranty of defective product, at our discretion. Other warranty concerns should be handled through the Fox Service program. Leaking shock seals less than 1 year from date of purchase, free from contamination, damage, or abnormal seal wear due to misuse can be considered for Warranty. FOX service information can be found here: https://www.ridefox.com/service.php?m=truck Ball Joints and Tie Rod Ends: These items are subject to normal wear over time. However, Ball Joints and Tie Rod ends less than 3 years from the date of purchase, that have been properly greased, maintained, and do not show signs of abnormal use can be considered for warranty. BDS Suspension's obligation under all warranties is limited to the repair or replacement, at BDS's option, of the defective material. BDS will cover the cost of ground shipping on warranty items, and a return shipping label if we require the warranty part to be returned to us. Any cost of removal, installation or reinstallation, expedited freight charges, incidental or consequential damages are expressly excluded from these warranties. Proof of purchase is required for all warranty claims.

Reviews & Questions