SKU:
BDS645FS
BDS645FS will built to outperform BDS Suspension engineered a 6-inch lift kit with long arm conversion for your 2003-2007 Dodge RAM 2500 and 3500 4WD diesel powered truck that maximizes performance on and off road. Designed to improve stance performance and capability this kit includes everything necessary to set your truck up right with clearance for up to 37" tires. BDS built the long lower control arms to reduce caster change through wheel travel which creates a more controlled feeling in the steering wheel. This long arm long arm system retains the factory triangulation of the arms which adds to the stability of the suspension system. Up front the lift kit includes diesel-specific Pro-Ride coil springs all four control arms plus mounting bracket forged drop pitman arm and track bar bracket for steering correction bump stops sway bar links and precision tuned NX2 or FOX 2.0 nitrogen charged shocks. In the rear this kit utilizes heavy duty cast steel blocks longer u-bolts and a matching set of NX2 Nitro or FOX 2.0 Performance shocks.
Pro-Ride Coil Springs
A pair of full-length diesel-specific progressive rate Pro-Ride coil springs are supplied to provide the correct lift height and smooth predictable ride across various terrains. Manufactured from high tensile steel our direct OE replacement coil springs are engineered with properly sized wire diameter. This results in maximum reliability without premature coil bind.
Steering Correction
To optimize steering geometry once lifted a forged drop pitman arm is used to minimize the steering angle and pair it with a heavy duty track bar drop bracket to keep them in phase through suspension travel while recentering the front axle.Tapered and roll-pointed leafs add flexibility and provide an even deflection rate Increased wheel travel and a softer ride from tapering allow smoother transition between leafs as compression takes place Higher articulation from bolt-style leaf alignment clamps prevents leafs from fanning out allowing leafs to twist and flex Multi-leaf progressive design for smooth ride Anti-friction pads provide a smooth and quiet ride Front Lift Height: 6 IN Front Lift Method: Coil Springs Installation Difficulty: moderate Installation Time: 6-8 Hrs Installation Tools: bit unibit Step Drill Bit-drill-puller pitmanArm-welder Rear Axle Option: 3_1_2_Inch_Axle Rear Lift Height: 4 IN Rear Lift Method: Block Rear Lift Option: Block Kit Shocks Included: Yes Measure rear axle tube before ordering. Some 4" axle models with dual overloads will require u-bolt 4068. Although unusual if driveline vibration occurs order appropriate transfer case drop kit 122602 (03-05 Diesel Auto) 122605 (06-08 Diesel Auto) or 122606 (03-13 Diesel Auto with OE mount P/N 52121938AA) available in options or t-case index kit. #122801 auto or #122802 for manual transmission. Optional transfer case drop kits fit automatic transmission models only. Exhaust modification will be required for dual rear shock kit 122009 on 6.7L Diesel models. If your Truck has had the steering gear box changed and the sector shaft diameter measures ~1-1/2"-1-5/8" you will need to add part # BDS082404 to your kit.
Pro-Ride Coil Springs
A pair of full-length diesel-specific progressive rate Pro-Ride coil springs are supplied to provide the correct lift height and smooth predictable ride across various terrains. Manufactured from high tensile steel our direct OE replacement coil springs are engineered with properly sized wire diameter. This results in maximum reliability without premature coil bind.
Steering Correction
To optimize steering geometry once lifted a forged drop pitman arm is used to minimize the steering angle and pair it with a heavy duty track bar drop bracket to keep them in phase through suspension travel while recentering the front axle.
Features-
Details-
Notes-
Wearable Parts - Limited Lifetime Warranty
BDS NX2 Series Shocks and BDS/Fox Performance Series Shocks:
Shock oil seals are not covered by this Limited Lifetime Warranty because they are subject to wear over time and use. At BDS's discretion, leaking shock seals less than 2 years from date of purchase, free from contamination, damage, or abnormal seal wear due to misuse can be considered for repair or replacement under warranty. A shock absorber is a wear item and over time will experience diminished damping resistance due to normal component wear. This is not a defect in material or workmanship and is therefore not warrantable. Defects in material and workmanship do not include such things as dented cylinders or bent rods caused by obvious side impact, rust or corrosion.
Fox Proprietary Shocks and Coil Overs:
Fox Proprietary parts are covered by their warranty and are not included in the BDS Warranty. BDS may offer to assist with the warranty of defective product, at our discretion. Other warranty concerns should be handled through the Fox Service program. Leaking shock seals less than 1 year from date of purchase, free from contamination, damage, or abnormal seal wear due to misuse can be considered for Warranty. FOX service information can be
found here: https://www.ridefox.com/service.php?m=truck
Ball Joints and Tie Rod Ends:
These items are subject to normal wear over time. However, Ball Joints and Tie Rod ends less than 3 years from the date of purchase, that have been properly greased, maintained, and do not show signs of abnormal use can be considered for warranty.
BDS Suspension's obligation under all warranties is limited to the repair or replacement, at BDS's option, of the defective material. BDS will cover the cost of ground shipping on warranty items, and a return shipping label if we require the warranty part to be returned to us. Any cost of removal, installation or reinstallation, expedited freight charges, incidental or consequential damages are expressly excluded from these warranties. Proof of purchase is required for all warranty claims.
